MicroCem-FB sample

Application guide

How to apply microcement with a Nikkolor kit

Follow the Nikkolor microcement workflow: assess the substrate, select preparation, mix, apply two coats, protect and plan handover using technical guidance.

Buyer guide

A microcement kit brings selected components together, but it does not replace the application instructions. The sequence starts with assessing the substrate and finishes with protecting the completed work. This overview follows the published Nikkolor system guides. Use the current technical data and the written project specification for the detail of each stage, rather than treating this article as a universal recipe.

Smooth MicroCem-FB surfaces in a warm living room with low sofas and timber detailing.

What should be checked before opening the kit?

Identify the precise substrate, its condition and the exposure expected in use. The system guides require instability, movement, moisture, waterproofing and flatness defects to be resolved before decorative work begins. Select the appropriate substrate section, not simply the example that looks closest to the intended room. There is no universal build-up for every surface.

Record the agreed primer or receiving layer and any reinforcement in the project documents. Compare that specification with the kit’s contents. A kit without mesh may still need reinforcement at repairs or joints, while mesh is not a replacement for movement joints. If the listed checks have not been passed, pause the work and ask for technical guidance.

How do I keep the colour and mixing consistent?

The published method says to measure the water and keep water, toner, equipment and mixing time consistent between batches. Toner is additional to the water, not a volume to subtract from it. Homogenise the toner, add water and toner, mix to a uniform colour, then add powder gradually while mixing mechanically. Scrape the sides and base and remix to a smooth, lump-free paste.

Read the current system guide for the actual water quantity and pot life before mixing. Do not borrow a ratio from another decorative range. The site specifically says not to retemper material that has started to stiffen. Order the powder and toner needed for the surface with batch consistency in mind, and keep the approved physical sample available during the work.

When do the primer and decorative coats go on?

Apply the substrate-specific primer or receiving layer and let it dry as required by its current technical data sheet. Then follow the two decorative coats in the published method, applied with a stainless-steel trowel. The next stage depends on actual drying and the recorded release criterion, not only on a time that has elapsed.

The guides distinguish reference conditions from a guarantee that the work can proceed. They state that times are for +20 C and are not a release by themselves, and that application is only above +10 C. Check the current instructions for the precise stage and the site conditions. If a surface has not reached its release condition, do not shorten the sequence to meet a handover date.

Is sanding the main way to finish the surface?

No. The system guide describes controlled trowel compression as the main finishing method, with careful hand detailing of corners while the material is workable. It explicitly says sanding is not a general finishing step. This is important when comparing a trowelled sample with an image of the finish.

Where one isolated detail needs refinement, follow the guide’s specific waiting, abrasive and sample-trial instructions, then remove dust. This article does not broaden that allowance into sanding the whole project. Ask Nikkolor if the finish needs more correction than the isolated-detail guidance covers, rather than improvising a new preparation or finishing cycle.

How do I choose protection and plan handover?

Protection follows the real service condition. Standard kits use Decor Finish; Pro kits use VetroLiquido PRP. Each has its own requirements and limits. Decor Finish without a slip-resistance additive is for walls and dry interior floors, and the floor add-on does not itself approve a wet floor. PRP follows its current data sheet and the project specification.

Do not swap a protective product into a coat sequence written for another one. The site also identifies a specific Semi-Gloss base requirement for Tapioca Matt with Decor Finish. Check the current product information and the finishes supplied before starting. Where there is a discrepancy or an unclear protection requirement, resolve it before application, not after the final decorative coat.

Handover needs more than a touch-dry check. The care page distinguishes drying, hardening and full cure, and says to keep the surface dry and uncleaned during the first week. Never drag furniture. Record the protection, cure dates and restrictions for the owner, and follow the current instructions for the actual project rather than promising an earlier return to use.

What should I decide before buying?

Choose the material, substrate preparation, kit size, protection and optional tint as one system. Kits come in 15 m² and 30 m² sizes; the purchase panel shows the selected contents and current price. Use the Colour Room, AI Visualiser and physical sample boards to agree the appearance. If you want the work installed, contact Lux Cement rather than assuming material supply includes application.

Common questions

Are tools and application labour included?

No. The kit exclusions include tools, labour, waterproofing and substrate repair materials.

Can I follow the clock alone between stages?

No. The system guides require actual drying and the recorded release criterion as well as the stated reference times.

Does dry mean cured?

No. Follow the care and protection guidance before cleaning, moving furniture or returning the surface to normal use.

Before you buy

  • Prices are AUD catalogue estimates, not quotations. Freight, tools, labour and substrate work are extra.
  • Confirm the current technical data sheets and a physical sample before specifying.